LT Swap Motor Mount Kit
Applications: Gen V LT motors (LV3, L83, L84, L86, L87, LT1, LT376, LT535, LT4, LT5, LT3, LT2, L8T)
Applications: 1967-1972 C10 C20 2wd blazer 1973-1987 (1988, 1989, 1990, 1991) GM Truck/SUV 4x4 and 2wd (K10, K20, K30, K5, V1500, V2500, V3500, C10, C20, C30, M1008, M1009)
SEE BOTTOM OF PAGE FOR LESS COMMON APPLICATIONS
What are the Gen 5 LT motor mount adapters?
The LT platform uses a different motor mount bolt pattern than the earlier small block or big block GM motors, because of this an adapter is needed for these engine swaps. Our adapters are designed to work with our frame side motor mounts but they are pretty universal if you are doing something custom. We build these super beefy, the plate is 3/8" thick! One piece design to make everything super strong!
Why use the Hogback Fab HD Motor Mounts?
So you just got done rebuilding your motor with all the power adders and are ready to put back in your truck and burn some rubber. Are you putting your motor on the stock mounts? Heck no! You need something that can stand up to the abuse. That is where our HD motor mounts come in. The are engineered to take on the highest HP race motors out there!
Comes Powder coated Gloss black with Grade 8 hardware (even the bolts to mount to the block and frame).
How easy is it to install the HD motor mounts?
Very Easy!
- If your motor is still in the truck, you will need to unhook the stock motor mounts and lift the motor high enough to remove/replace the mounts. The motor will need to safely be lifted with an engine hoist. Make sure nothing will get stretched/broken like wires, fuel lines, etc.
- Remove the stock motor mounts from the block and frame.
- Loosely bolt on the block side HD mount to the block and the frame side to the frame. We say loosely so you can adjust the mounts around when lowering the engine.
- Lower the motor on to the new frame side mount. Note: as we all know these frames are noodle and move around a lot. It may take some moving around of the mounts up, down, forward, rearward for the main bolt to pass through.
- Slide the 9/16" main bolt through the two motor mount halves and tighten down.
- Tighten the frame and block side mounts
- Reconnect anything you may have unhooked when lifting the motor.
- Enjoy your new found strong mounts!
- After 100 miles make sure to go check all bolts are tight.
Note: For LT motor swaps in 67-87 GM truck/suv the stock location of the A/C compressor can not be retained, there are many companies in the aftermarket offering up high A/C mounts. For trucks that are 4x4 crossmember it will clear if you are using a 4x4 pan or aftermarket holley swap pan on the motor. Some very rare occurrences based on frame tolerances (and super old frame rivets shifting) a notch of the crossmember or spacing up the mount a little may be needed. On 2wd trucks the stock crossmember will be fine.
Since our mount is based off the OEM mount, it can also fit the below applications:
Make Model Year
Buick
Apollo 1973-1975
Century 1977-1980
Commercial Chassis 1991-1996
Le Sabre 1978, 1982
Regal 1977-1980, 1982-1984
Roadmaster 1991-1996
Skylark 1968-1971, 1977-1979
Special 1968-1969
Cadillac
Brougham 1990-1992
Commercial Chassis 1992-1996
Fleetwood 1993-1996
Seville 1976-1980
Chevy
Bel Air 1973-1975, 1981
Blazer 1973-1987
Camaro 1972-1992
Caprice 1975-1996
Chevelle 1973
CK Pickup 1973-1991
Commercial Chassis 1991-1994
Corvette 1980
El Camino 1973-1987
G-Series 1975-1996
Impala 1973-1985, 1994-1996
Laguna 1973-1976
Malibu 1973-1983
Monte Carlo 1973-1988
Nova 1973-1979
P-Series 1975-1999
Suburban 1973-1987, 1989-1991
GMC
Caballero 1978-1987
CK Pickup 1975-1991
G-Series 1975-1996
Jimmy 1973-1987
P-Series 1975-1999
Sprint 1973-1977
Suburban 1975-1987
Oldsmobile
Calais 1978-1980, 1982-1984
Custom Cruiser 1992
Cutlass 1975-1976, 1978-1984
Eighty-Eight 1977, 1981-1982
Omega 1973-1979
Starfire 1977-1979
Pontiac
Bonneville 1983-1986
Catalina 1977-1981
Firebird 1973-1992
Grand Am 1978-1980
Grand Prix 1974-1987
LeMans 1973-1982
Parisienne 1977-1986
Phoenix 1977-1979
Sunbird 1978-1979
Ventura 1973-1977
Materials
Materials
Gloss black powder coated steel.
Product comes welded
Hardware is grade 8
Bolts and Lock washers for motor side and for frame side
Bushings are Polyurethane
Sleeves are Chromoly
Shipping & Returns
Shipping & Returns
$16 shipping on orders valued $350 and under
Free shipping on orders $351 and up!
Returns accepted 30 days from delivery. Use the contact form to email us and get a return authorization
-
Free Shipping
USA ORDERS
$15 shipping on orders valued $350 and under
Free shipping on orders $351 and up!
Canadian Orders
Orders over $751 USD ship FREE!
Note: Price does not include Duties or Taxes, these will need to be paid
by the customer. -
Hassle-Free Exchanges
Order the wrong part? Send us
an email on the contact form and we can help you get it all sorted out!